S/MIME & IRM Together
How do S/MIME and IRM work together? Can you have users sign and or encrypt their messages with S/MIME and then also have some IRM policies in the background? I'm not sure of the exact scenario, but in...
View ArticleUser mailboxes have more server-side rule options then shared mailboxes?
I was hoping to set up some server-side rules to keep a shared mailbox clean. The goal was to have some rules to move incoming messages to specific folders based off words in the subject. I opened...
View ArticleRemoved DAG but Shadow Redundancy Queue is Stuck
Hello,I currently have 3 Exchange servers setup in Co-Existence (EX2010, EX2013A, EX2013B). The 2010 Server is still the public facing server.I had the two 2013 servers setup in a DAG which I could not...
View ArticleQuestions about sending and receiving encrypted email
When you send out an unencrypted, digitally signed message or a message with your public key attached (so you can send encrypted messages to them in the future), can't that message be intercepted and...
View ArticleExchange 2010 internal only recieve connectors
I created an internal only receive connector using only the anonymous permission this worked but resolution did not. I found to get resolution I need to enable externally secured this required exchange...
View ArticleCannot enable custom DSN
Hello,I am trying to create a custom DSN to send a NDR alerting the internal sender that his/her mail has been rejected due to profanity. I created a DSN 5.2.9 with the message "Your message appears...
View Articleoutbound emails stuck in queue - 451 error
Hi,We received the below error message in particular domains."451 4.4.0 Primary targeted IP address responded with: "421 4.2.1 Unable to connect." Attempted failover to alternate hosts, or delivery...
View Article2 Edge servers with different HELLO FQDN
I have 2 Edge servers subscribed to 1 site. How can I specify HELLO FQDN for each my edge server, because they have 2 different public IPs and 2 different public DNS names?
View ArticleExchange 2013 SP1 Console powershel access denied and my emails remains in...
hello ,i have exchange 2013 SP 1 , console powershel run in erruer access denied and my emails remains in Draft.i have 2 servers cas (NLB) and 2 server MBX (DAG)any help plz. COMMENTAIRES : Connexion à...
View ArticleRelay Receive Connector - Recipient Limit is not respected
Hi,I have configured a Relay Receive Connector for an application and I set the Recipient limit for it, 50 recipients.Unfortunately this limit is not being respected, the application can send emails to...
View ArticleMail not flowing, unable to telnet to port 25 (Exchange 2013)
We have an Exchange 2013 server which was working fine, but after a failed CU2 upgrade, we rolled back to the restore and since then mail isn't flowing. All emails go into drafts.We can telnet to port...
View ArticleExchange 2013 Address Book Policy Routing Agent Issue with Mailboxes Hidden...
When the AddressBookPolicyRoutingEnabled attribute is enabled by running Set-TransportConfig -AddressBookPolicyRoutingEnabled $True, I am having an issue with delivery failures for mailboxes that are...
View ArticlePublic Folders forwarding to internal address
Hello, we have set forwarding from Public Folder to internal user and selected to forward to both addresses but the mail is only delivered to users mailbox, not to PF, the same is with transport rule,...
View ArticleMail Flow Issue In Exchange Server 2010
Hello,I have an on-premises environment where I have an exchange 2010 hub and edge server. I have 4 domains. All my emails are routed through edge server to the internet. When I send an email from my...
View ArticleExchange 2013 Frontend Receive Connector - cannot telnet port 25
Hello There,I’m going to proceed with migration form exchange 2007 to 2013 but just encounter problem.I can telnet port 25 form new Exchange 2013 server but cannot telnet it form any other computer...
View ArticleMessages going to junk email folder
Hi,We have exchange 2013 deployed and from few days some emails on all users are going to their outlook 2007, 2010 Junk-Email folder.How can i stop same from Exchange 2013 Server side?Best Regards,...
View ArticleError in upgrading from Exchange 2010 SP2 RU6 to Exchange 2010 Sp3.Setup...
Hi We are getting below error on few of CAS servers when we try to upgrade to Exchange 2010 SP3 while uninstalling the IU for SP2"Setup wizard for update rollup6 for Exchange Server 2010 Service Pack 2...
View ArticleExchange 2013 SP1 attachment icon
Hello, our Exchange acts strange when it comes to attachments. The behavior seems to be random. Sometimes in OWA and Outlook the attachment icon is not visible but the attchment is in fact there...
View ArticleExchange Server 2013: Not Sending and Receiving email
Hello, I have a new Exchange Server 2013 install single node and i am having problems sending and receiving email. When testing from https://testconnectivity.microsoft.com/ it fails at the last...
View ArticleTest-Mailflow messages ends up in Poison Queue
Hi,i've a fresh install of Exchange 2013 SP1. When I test the mailflow with the Test-Mailflow cmdlet, the messages end up in the poison queue. Other mails sent through OWA or Outlook were submitted...
View Article